Hi, I want to install a handle downside of the board. My local shaper told me that if the board is not reinforced could put in compromise the board structure. Any advice would be appreciated. I don t know if the board is reinforced near the rail box.
Thanks
Handle on a flint
- coolas
- Messages : 14945
- Inscription : lun. août 10, 2009 1:24 pm
- Localisation : Ambassadeur Seignosse, 1m67, 97kg
- Contact :
Re: Handle on a flint
You can see the construction under the "Techno" tab on its web page.
The hull is made with a 3mm PVC sandwich, so no issue there, it is as strong as the deck.
The shaper will need of course to encase the handle in some waterproof foam (e.g PVC) both for support and as a safety to avoid water entry if cracks appear later.
Disclaimer: I am not part of the Gong team.
The hull is made with a 3mm PVC sandwich, so no issue there, it is as strong as the deck.
The shaper will need of course to encase the handle in some waterproof foam (e.g PVC) both for support and as a safety to avoid water entry if cracks appear later.
Disclaimer: I am not part of the Gong team.
2019: 7'3" Fatal 105L, Alley 7'8" 105L & 8'1" 120L, Zero 9'0" 115L
2022: Mob 7'6" cool 120L, Alleys custom 7'10" 112L & 8'1" 114L
2023: Karmen custom 7'11" 118L
Surf: 9'1" XTR proto glider
2022: Mob 7'6" cool 120L, Alleys custom 7'10" 112L & 8'1" 114L
2023: Karmen custom 7'11" 118L
Surf: 9'1" XTR proto glider
- Ours
- Site Admin
- Messages : 19800
- Inscription : mar. juin 12, 2007 11:50 am
- Localisation : La Baule / France
- Contact :
Re: Handle on a flint
Hello,
you can do it if you do it seriously.
1/ Use a nice handle, one that is covered by fiber layers at the end.
2/ Do the hole for the handle at the right place, 10cm forward OS box or a little less.
3/ Do a nice scarf on the bottom lamination to let minimum 3 strong layers of carbon fiber over the handle by the end.
4/ Glue the handle with slow resin and fiberglass.
5/ Sand a little to make it clean.
6/ Put 3 to 5 layers of carbon over the handle and on all the large scarf you did (10cm around the handle). Press it with weight of you can.
7/ Sand it and do the finish.
If you land super hard and you bend the board a lot, some cracks can appear. I never saw it, but it can happen. You just have to repair. Easy.
Thanks,
you can do it if you do it seriously.
1/ Use a nice handle, one that is covered by fiber layers at the end.
2/ Do the hole for the handle at the right place, 10cm forward OS box or a little less.
3/ Do a nice scarf on the bottom lamination to let minimum 3 strong layers of carbon fiber over the handle by the end.
4/ Glue the handle with slow resin and fiberglass.
5/ Sand a little to make it clean.
6/ Put 3 to 5 layers of carbon over the handle and on all the large scarf you did (10cm around the handle). Press it with weight of you can.
7/ Sand it and do the finish.
If you land super hard and you bend the board a lot, some cracks can appear. I never saw it, but it can happen. You just have to repair. Easy.
Thanks,
GONG owner and shaper
-
- Messages : 11
- Inscription : lun. févr. 15, 2021 7:09 pm
Re: Handle on a flint
Thank you very much to both of you